How to Measure Your Hot Tub for a Custom Cover

Worried you'll get it wrong? That feeling isn't a you problem. The instructions across this industry genuinely contradict each other. This page replaces the noise with one method: the one our factory actually builds from. One tape measure, about 10 minutes.

Since 2008 We build to any dimension

Three rules carry everything

1. Measure your spa, not your old cover. Covers sag and shrink with age, and a sagging cover passes its mistakes to the next one. If your old cover fit well, use it afterward to double-check. Never as the source.
2. Round up to the nearest inch. We build to any dimension (1/4", 1/2", 3/4"), but bigger is always the safe direction. Slightly large works fine. Slightly small may not fit at all. Worried? Add an extra 1/2".
3. Everything is in inches. No feet, no centimeters.
Mike "kept me grounded while I made sure I measured the hot tub correctly."Verified customer review, April 2026. Want a human to double-check your numbers before you order? Email us. People do it every day.

What you'll need: a rigid metal tape measure and, only if your corners are rounded, a framing square or our free printable radius template.

Step 1 · Which kind of spa do you have?

This decides how you measure, and it's the step most guides skip. Pick yours:

Type A measuring: outside edge of the acrylic shell to outside edge...
Type B measuring: two valid builds. Option 1 (standard)...
Type C measuring: the overall OUTSIDE of the shell...
Type D measuring: measure the opening, then ADD 6" to 8"...
Feeds: Dimension A + Dimension B

Step 2 · Length and width

Warning: Before you stretch the tape: the fold runs across Dimension A. Whichever number you enter as A is the side that gets cut in half by the hinge. Most people fold the long side. If the half-open cover needs to leave your control panel reachable, check what that means for your spa first. The order page draws the fold line live as you type.

Measure per your spa type above, at the widest points. Tape reads 91 1/4"? Enter 92. Write both numbers on the worksheet.

Feeds: Dimension C (Radius)

Step 3 · Corner radius

The field people freeze on, and it's more forgiving than it feels. The radius is just how far from the corner the curve starts.

Framing square method

Hold the square against one corner, both legs touching the straight edges. Measure along one leg from the corner of the square to where the acrylic first touches it. That's your radius.

No square? Scissors beat geometry.

Print the radius template sheet, hold it over your corner, match the curve, cut out the winner, confirm on the corner.

Square corners? Radius is 0. Between sizes? Go smaller: a slightly smaller radius extends the cover further over the corner. Radius is the one number where smaller is the safe direction.

Feeds: Skirt Length

Step 4 · Skirt length

The skirt has one job: keeping the sun off your acrylic. UV is why so many spas wear a bleached band around the top.

So don't measure the skirt you have. Measure the skirt you need: from the bottom of your existing cover straight down to where the acrylic stops and the cabinet starts. If your current skirt is too short (usually why the acrylic faded), copying it re-orders the problem.

Feeds: Strap Placement + Strap Length

Step 5 · Straps

Placement: pick where the four straps land (handle sides, hinge sides, all 4 sides, or corners). Match where your cabinet's clips are mounted today.

Length: bottom edge of the cover down to your existing clip, not including the clip. Your strap should be at least 1.5" longer than your skirt so it reaches past the flap.

The escape hatches

Odd or unique shape

We build from a template you make in about 15 minutes: clear painter's tarp, masking tape, permanent marker. Drape, tape, pull taut, write the word "Top" on it first, then trace the shell leaving 1/4" to 1/2" extra. Add your name and phone number. The "Top" matters: without it a cover can be built as a mirror image of your spa. Email us for mailing instructions.

Obstructions

Speaker hoods, handrails, steps, raised control panels: buildable with cut-outs and flaps at additional cost. Contact us before ordering.

Not sure about anything?

Send us your numbers and photos before you order. A human reads them.

Before you order: the 60-second self-check

  1. Both dimensions measured on the SPA, at the widest points, in inches
  2. Rounded UP to the next whole inch
  3. Old cover fit well? Your numbers should land close to it. A sagging cover reads smaller: trust the spa
  4. Radius from the square or the template, not eyeballed
  5. Skirt measured to where the acrylic ends, not copied from the old flap
  6. The side you want folding in half is entered as Dimension A
  7. Numbers on the worksheet, then typed in carefully

Questions people actually ask

Do I measure the tub or the cabinet it sits in?

The acrylic shell's outside edge for most spas (Type A). Only Type B option 2 measures the cabinet. Never the box for a Type A spa.

Can I just use my make and model instead of measuring?

Model databases are a great cross-check, and ours is one of the biggest. But manufacturers changed dimensions year to year, so confirm with a tape. When your tape and a database disagree, trust your tape.

What if I'm off by half an inch?

Model databases are a great cross-check, and ours is one of the biggest. But manufacturers changed dimensions year to year, so confirm with a tape. When your tape and a database disagree, trust your tape.

Does the foam count in the skirt measurement?

No. The skirt is measured from the bottom of the cover, below the foam, down the acrylic. You never measure the foam itself.

Can a 96x96 cover work on my 92x92 spa?

It'll sit there, but four extra inches means overhang, corner gaps, and a bad seal. Measure and round up one inch, not four.

What's the taper? Do I need to measure it?

No. Taper (thicker at the middle so rain runs off) is our geometry, not your measurement. You just pick a thickness option.

Which way should the fold go?

See Step 2. Long side halved is standard; reaching your control panel with the cover half-open is the reason to do otherwise.

My measurement seems odd. Is it even orderable?

We build to ANY dimension. There's no size list your spa has to match.